NETGEAR Network Router FVS328 User Manual

c. Securely insert the Ethernet cable from your broadband  
MODEL  
modem into the Internet port (B) on the FVS328.  
FVS328  
Broadband ProSafe VPN Firewall with Dial Backup  
PWR TEST Modem  
IN TER N ET  
LO CA L  
LNK  
100  
ACT  
LNK/ACT  
1
2
3
4
5
6
7
8
Internet Port  
B
Start Here  
Internet Port  
Local Port 7  
Power  
Test  
LO CA  
10/100M  
L
1
2
V
DC  
1
.
2
A
M
O
DEM  
IN TERN ET  
8
7
6
5
4
3
2
1
d. Check the status lights and verify the following:  
Follow these instructions to set up your router.  
Broadband modem  
Power: The power light goes on when your turn the  
Verify That Basic Requirements Are Met  
firewall on.  
d. Securely insert one end of the Ethernet cable that came with  
your firewall into a LAN port on the router such as LAN  
port 7 (C), and the other end into the Ethernet port of your  
computer (D).  
Test: The test light turns on, then goes off after less than  
Assure that the following requirements are met:  
a minute.  
You have your broadband Internet service settings handy.  
Local: A Local light on the router is lit. If no Local  
lights are lit, check that the Ethernet cable connecting  
the powered on computer to the router is securely  
attached at both ends.  
The computer is configured to obtain an IP address  
automatically via DHCP. For instructions on how to do this,  
please see the Reference Manual on the Model FVS328  
Resource CD.  
Internet: The Internet light on the firewall is lit. If the  
Internet light is not lit, make sure the Ethernet cable is  
securely attached to the firewall Internet port and the  
powered on modem.  
D
1. CONNECT THE FIREWALL  
a. Turn off your computer and cable or DSL modem.  
LO CA  
10/100M  
L
1
2
V
D
C
1
.
2
A
M
O
DEM  
IN TER  
N
ET  
8
7
6
5
4
3
2
1
b. Disconnect the Ethernet cable (A) which connects from  
Broadband modem  
3. LOG IN TO THE FIREWALL  
your computer to the broadband modem.  
C
a. From your PC, launch your Internet browser.  
Local Port  
b. Connect to the firewall by typing http://192.168.0.1 in the  
address field of Internet Explorer or Netscape® Navigator.  
2. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE  
Warning: Failure to restart your network in the correct  
sequence could prevent you from connecting to the Internet.  
A
a. First, turn on the broadband modem and wait 2 minutes.  
b. Now, turn on your firewall.  
c. Enter admin for the router user name and password for the  
Broadband modem  
router password, both in lower case letters.  
c. Last, turn on your computer.  
d. After logging in to the router, you will see the Internet  
connection Setup Wizard on the settings main page.  
Note: If software usually logs you in to the Internet, do not  
run that software or cancel it if it starts automatically.  
 

Miele Oven H 4744 BP User Manual
Mr Heater Gas Heater HS25NG LP User Manual
NEC Computer Hardware 40 GB User Manual
Nikon Camcorder S6100 User Manual
Nikon Camera Lens 25101 User Manual
Nortel Networks Switch 1000ASE XD User Manual
Novatel Car Satellite TV System DL V3 User Manual
Oregon Scientific Thermometer THR2 8 User Manual
Pacific Cycle Swing Sets 22 PS245 User Manual
Panasonic Bluetooth Headset BH 606 User Manual